Summary
MAGNET_GENERAL_CATALOG_2019
DEMAGNETIZERSMAGNETIC TOOLS & EQUIPMENTFOR WELDING OPERATIONLIFTINGMAGNETMAGBORE*CHIP & SLUDGE ENVIRONMENTALMAGNETIZER AND MAGNETIC EQUIPMENTCONVEYANCE EQUIPMENT EQUIPMENTDEMAGNETIZERFOR CONVEYANCEMAGNETICSEPARATORSPOWERFUL MAGNETICSEPARATORSMEASURING MEASURING MAGNETICTOOLS INSTRUMENTS MATERIALSModel KMDY POWERFUL TABLE TYPE 3-PHASE AC DEMAGNETIZERStrong magnetic field to enhance demagnetization effect!KMDY-1※Cable 2 m included.Model KMDS DRIP-PROOF DEMAGNETIZERModel KMD-F INVERTER CONTROLLED DEMAGNETIZERLess electric power and enhanceddemagnetizing performance!Stronger magnetic field producedthan standard table type!AHL 2L 1L3060ALBBBB1N-φdHB[Application]Designed to remove or reduce residual magnetism by passing magnetizedworkpieces over the demagnetizing face.[Features]●The use of a 3-phase AC power source produces a more powerfulmagnetic field to effectively demagnetize workpieces having propertiesand shapes that are difficult to demagnetize with the conventional type.●This demagnetizer especially exhibits its high-performance on ringshapedworkpieces such as bearing-assembled products and gears.●The high heat dissipation design permits continuous operation. [mm(in)]DimensionsModelPower SourcePower CapacityWorking RateEffective Demag. WidthBLHMassKMDY-13-phase 200 VAC, 50/60 Hz0.43/0.36kVA(2.15A/1.8A) (50/60Hz)100%ED140(5.51)200(7.87)200(7.87)150(5.90)14kg/30.8 lb[Application]These demagnetizers produce a strong magnetic filed on the surface by use of an ACpower source to demagnetize workpieces on a belt which runs over close to the surface.[Features]●The demagnetizers are of drip-proof construction. They will not fail if wetted bygrinding fluid or cooling water.●These can be incorporated in belt type grinders or other automatic and continuousgrinders.●The very strong demagnetizing force generated provides some margin for theclearance on the surface to allow a belt conveyor to run over the work face.KMDS-2A〈Demagnetizing direction〉KMDSKMDS[mm(in)]ModelPower SourcePower CapacityDimensionsWorking Rate(Current)B L H B? Nφd L? L?MassKMDS-1A200VA(1A) 50% ED 150(5.90) 9.0kg/19 lbSingle-phaseContinuous operation206(8.10) 100(3.93) ? 2 8.5 260(10.2) 235(9.25)KMDS-2A 400VA(2A) 200(7.87) 13.5kg/30 lb200 VAC, 50/60 Hzallowed when cooled(0.33)KMDS-3A800VA(4A)by water.400(15.7) 350(13.7) 120(4.72) 120(4.72)4410(16.1)380(14.9)41.0kg/90 lb※Cable 2 m included.※No switch is incorporated.※A different-voltage type (special type) is also available.ModelPower SourceKMD-F20PowerCapacityOutputPrecaution for useCool these demagnetizers by splashing water at normal temperature. 50% ratedwhen used dry. (20 minutes power on and 20 minutes pause)[Application]These demagnetizers produce an alternating magnetic field on thesurface by use of an AC power source, through which workpieces arepassed to remove the magnetism remaining on their surface.[Features]●Demagnetization is carried out by varying (sweeping) a frequencylower than commercial frequencies from a lower point to a higherpoint. This design has improved the demagnetizing performancewithout increasing the amount of electricity to use.●The demagnetizing section is of the same dimensions as theconventional table type demagnetizer (KMD-C). With the same outputcurrent (AC effective value) as the conventional model, the residualmagnetism in workpieces (SKH material) can be reduced to one third.●Workpieces are demagnetized by passing them over the demagnetizingsurface at a constant speed, as with the conventional model.●Continuous power on specification, but heat generated in thedemagnetizing part is less than the conventional model.●A demagnetizing output variable resistor is provided on the electricalunit that can vary the output current (AC effective value) in a range of100% and 70%. This feature achieves demagnetization of low-carbonsteel like S45C by less power (70%) than the conventional model.[mm(in)]WorkingRateEffective Demag.DimensionsMassWidthWidth Length Height130(5.11) 200(7.87) 120(4.72) 80(3.15) 6.5kg/ 14 lbDemagnetizing section KMD-F20 Single-phase 100 VAC,±20V200VA(2.7A)100% EDElectrical unit EHD-20A 50/60 HzMAX5A? 140(5.51) 175(6.89) 260(10.2) 4.5kg/9.9 lb123Demagnetizing section KMD-F30 Single-phase 200 VAC,±30V180(7.08) 300(11.8) 200(7.87) 120(4.72) 21.0kg/ 46 lb400VA(3.4A)100% EDElectrical unit EHD-30A 50/60 HzMAX7.5A? 220(8.66) 175(6.89) 290(11.4) 5.8kg/ 13 lbThe main unit is provided with a 2 m cable.
