BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

MAGNETIC TOOLS & EQUIPMENTFOR WELDING OPERATIONLIFTINGMAGNETMAGBORE*CHIP & SLUDGE ENVIRONMENTALMAGNETIZER AND MAGNETIC EQUIPMENTCONVEYANCE EQUIPMENT EQUIPMENTDEMAGNETIZERFOR CONVEYANCEMAGNETICSEPARATORSPOWERFUL MAGNETICSEPARATORSMEASURING MEASURING MAGNETICTOOLS INSTRUMENTS MATERIALS127DEMAGNETIZERSModel KMDP PEN TYPE DEMAGNETIZERKMDP-16AKMDH-P21KMDH-5AFor both AC and DCφ15.5ON/OFF switch26(Demagnetizing area)264Model Power Source Source Capacityφ30NP.Effective Demag.Widthφ35.5DC jackModel KMDH HANDY TYPE DEMAGNETIZEREnvironmentallyfriendlyModel Battery Rating MassKMDP-16A 2.4V2000mAh 0.3kg/0.6lb※The AC adapter (input 100 VAC, 50/60 Hz, output 2.7 VDC, 0.5 A,cord length 1.9 m) is included as a standard accessory.DimensionsWidth Length HeightKMDH-5A Single-phase 100 VAC, 50/60 Hz 80/70VA 50(1.96) 86(3.38) 106(4.17) 119(4.68) 2.3kg/5.1 lb※The height is up to the grip.※2 m cord is included. The plug is provided with a ground pin.※A different-voltage type (special type) is also available.※The power plug is of tracking resistance type.Model KMDH-P PINPOINT TYPE DEMAGNETIZERModel KMDC TOOL DEMAGNETIZERNonwatertightNonwatertightNonwatertightNonwatertightKMDC-40[Application]Recommended where magnetism on the surface of metallic workpieces in general needs to bereduced in a limited area or locally.This is useful to completely eliminate weak magnetism that remains locally in jigs and workpiecesafter they have been demagnetized by a large demagnetizer. It is also useful for demagnetizingcutters of machines and punches and guide pins of press dies while they are mounted.[Features]●Compact and powerful as a rare earth magnet having strong magnetic force is used at the endof the rotary magnetic field.●A re-chargeable battery is used as a power source of the motor. No need to replace the battery.Power can also be supplied with the included AC adapter if the battery has reached its life.●Simple construction and simple appearance.●An environment friendly nickel hydrogen battery is used.[Application]Suitable for demagnetizing tools such asdrills, cutting tools, cutters and magnetizedslide calipers. These can also be used fordemagnetizing large steel plates partially.[Features]●Compact and handy.Working rate 70% ED (Power on 7 minutes and pause 3 minutes)8838503050Numeric thermo label□21(DemagnetizingCautionarea)plate79161240150How to use[mm(in)]Model Power Source Source Capacity Working Rate Remote Operation Demag. Hole Dia. MassKMDC-40 Single-phase 100 VAC, 50/60 Hz 72/67VA●The demagnetizer is turned on while thepushbutton switch is held pressed andturned off when you release it.●The button must be held pressed whiledemagnetizing is going on.●Turn off the demagnetizer after it has beenmoved more than 100 mm away from thedemagnetized workpiece.20% ED,1 minute max.Momentary input byuse of pushbuttonφ40(1.57)MassModel Power Source Source Capacity Working Rate MassKMDH-P21 Single-phase 100 VAC, 50/60 Hz 570/380VA 20% ED, 10 seconds max. 3kg/6 lb※The power plug is of tracking resistance type.●Power is applied only while the pushbutton switch isheld pressed for demagnetization.●Turn off the demagnetizer after moving it away more than100 mm from the demagnetized object.●If the demagnetizer is turned onfrequently, the body temperaturerises. If the temperature rises toohigh, it is indicated by an overheatalarm seal. Stop using it for a while.How to use[Application]An alternating field is produced at the tip and bottom by an AC power source, which is broughtinto contact with a workpiece and then moved away. Then the magnetic flux density on thesurface is reduced locally. This demagnetizer works effectively in demagnetizing molds and largematerials partially.[Features]●Since this demagnetizer produces a strong magnetic field at the tip, it can effectivelydemagnetize places that are difficult to demagnetize with a conventional table type or handytype demagnetizer.●The magnetizing effect is powerful, but the attracting force is not strong. Thus, the tip partcan be brought into contact with a small area for easy handling.●A thermo label is attached to the tip part, which warns a temperature rise due to frequent,repeated use. When the thermo label appears, stop using the demagnetizer until it goes out.Demagnetization of magnetized tools such as drills,reamers and cutters and measuring instruments!Overheatalarm sealattachedDisplayplateSpec. platePower cord: 2 mVCTF (1.25 ? , 3-core)Plug with ground pin[Application]Easy demagnetization of a wide variety of magnetizedobjects including tools such as drills, milling cutters,reamers and cutters, round workpieces and measuringinstruments such as slide calipers.[Features]●Light weight, compact and easy operation.●Fine chips sticking by attraction to drills, reamers, etc.can be removed while they remain mounted onmachines.※Cord length 2.5 m (with curled cord).※The power plug is of tracking resistance type.[mm(in)]0.9kg/2 lb