BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

MAGNETIC TOOLS & EQUIPMENTFOR WELDING OPERATIONLIFTINGMAGNETMAGBORE*CHIP & SLUDGE ENVIRONMENTAL MAGNETIZER AND MAGNETIC EQUIPMENT MAGNETICPOWERFUL MAGNETIC MEASURING MEASURING MAGNETICCONVEYANCE EQUIPMENT EQUIPMENT DEMAGNETIZER FOR CONVEYANCE SEPARATORSSEPARATORSTOOLS INSTRUMENTS MATERIALS151POWERFULMAGNETICSEPARATORS■?M odel PCMB Comparison of sanitary magnetic barsType ModelSurface Max. MagneticFlux Density※Note that if the separators are used in environment exceeding the working temperature upper limit, the attraction and holding power may drop due to reduction of magnetism.An example of PCMB2 special fabricationWorking Temp.Upper LimitRemarksPowerfulPCMB0.8 TeslaStandard type.Fine pitchPCMB-AM1.0 Tesla80℃(176°F)Pole area increased by 1.5 times. Catch amount andcollection rate increased.Super powerfulPCMB-APCMB-U1.2 TeslaSemi heat-resistantPCMB-QT0.8 Tesla150℃(302°F)Low cost type.Heat-resistant powerfulPCMB-TPCMB-AT1.0 Tesla240℃(464°F)Highest working temperature upper limit in this Series.Wear resistant PCMB-J 1.3 TeslaHighly resistant to wear and corrosion and longer life.80℃(176°F)Double-pipe PCMBD-A 0.8 Tesla Double-pipe for easy cleaning of attracted iron powder.Model PCMB SANITARY MAGNETIC BARPCMB2-20■?P owerful magnetic bar[Application]Suitable for installation as an iron-removing gate in powder materials transfer ducts orliquid passages and tanks. Can be incorporated flexibly to expand a range ofapplications.[Features]●High grade finish of sanitary specification.●Various lengths are available for a desired combination.●High power magnetic bars: a powerful rare earth magnet having a property value of1.2 T (12,000 G) or 1.35 T (13,500 G) or over is incorporated and the surfacemaximum magnetic flux density is 0.8 T (8,000 G) or 1 T (10,000 G) or over.●Since a permanent magnet that maintains a strong magnetic force almostperpetually is used, the running cost can be reduced significantly.●These are of waterproof construction to allow installation in liquid.●To increase the rate of removal of metallic powder of very weak magnetism,PCMB-U type that has a surface magnetic flux density of 1.2 T (12,000 G) is alsoavailable.●Special sizes are also available.[mm(in)]Model Casing Pipe Built-in Permanent Surface Max. Magnetic Working Temp.Without tapped hole With tapped hole Length Diameter Material Surface finish MagnetFlux DensityUpper LimitMassPCMB-10PCMB2-1095(3.74)0.35kg/0.77 lbPCMB-15PCMB2-15145(5.70)0.5 kg/1.10 lbPCMB-20PCMB2-20194(7.63)0.7 kg/1.50 lbNd rare earth typePCMB-25PCMB2-25244(9.60)0.85kg/1.87 lbφ25※1#4000.8T80℃buffedProperty value(8000G)(176°F)PCMB-30PCMB2-30295(11.6)SUS3041.05kg/2.31 lbPCMB-35PCMB2-35343(13.5)(0.98)SUS3041.2 kg/2.64 lb1.2T(12,000G)PCMB-40PCMB2-40393(15.4)1.4 kg/3.08 lbPCMB-50PCMB2-50493(19.4)1.75kg/3.85 lbPCMB-60PCMB2-60592(23.3)2.1 kg/4.63 lb※A casing pipe of SUS316 is also available.※1 A casing pipe ofφ19 is also available.※For the models with tapped holes, the tapped hole is M6-P1.0 and 7 mm deep, locatedinthecenteroneachendface.AmodelofM5,M8,M10orM12isalsoavailable.■?S uper powerful magnetic bar※In order to increase the surface magnetic flux density, the wall thickness of the pipe needs to be decreased. If it isdecreased, however, the strength may drop or the pipe may be deformed or broken. Therefore, for the safety reason,pipes of thickness thinner than the current thickness will not be manufactured.[mm(in)]Model Casing Pipe Built-in Permanent Surface Max. Magnetic Working Temp.Without tapped hole With tapped hole Length Diameter Material Surface finish MagnetFlux DensityUpper LimitMassPCMB-A15PCMB2-A15145(5.70)0.5 kg/1.10 lbPCMB-A20PCMB2-A20194(7.63)0.7 kg/1.54 lbPCMB-A25PCMB2-A25244(9.60)Nd rare earth type0.9 kg/1.98 lbPCMB-A30PCMB2-A30295(11.6)φ251T1.1 kg/2.42 lbPCMB-A35PCMB2-A35343(13.5)(0.98)SUS304Property value(10000G)1.2 kg/2.64 lbPCMB-A40PCMB2-A40393(15.4)1.35T(13,500G)1.4 kg/3.08 lbPCMB-A50PCMB2-A50493(19.4)1.8 kg/3.96 lbPCMB-A60PCMB2-A60592(23.3)2.1 kg/4.63 lb#40080℃PCMB-U10APCMB2-U10A95(3.74)0.3 kg/0.66 lbbuffed(176°F)PCMB-U15APCMB2-U15A145(5.70)0.5 kg/1.10 lbPCMB-U20APCMB2-U20A194(7.63)0.7 kg/1.50 lbNd rare earth typePCMB-U25APCMB2-U25A244(9.60)0.9 kg/1.98 lbφ25.11.2TProperty value(12000G)PCMB-U30APCMB2-U30A295(11.6)(0.99)SUS316L1.1 kg/2.42 lbPCMB-U35APCMB2-U35A343(13.5)1.2 kg/2.64 lb1.38T(13,800G)PCMB-U40APCMB2-U40A393(15.4)1.4 kg/3.08 lbPCMB-U50APCMB2-U50A493(19.4)1.8 kg/3.96 lbPCMB-U60APCMB2-U60A592(23.3)2.1 kg/4.63 lb※A casing pipe of SUS316 is also available. (Models PCMB-A)※For the models with tapped holes, the tapped hole is M6-P1.0 and 7 mm deep, locatedin the center on each end face. A model of M5, M8, M10 or M12 is also available.※In order to increase the surface magnetic flux density, the wall thickness of the pipe needs to bedecreased. If it is decreased, however, the strength may drop or the pipe may be deformed orbroken. Therefore, for the safety reason, pipes of thickness thinner than the current thickness willnot be manufactured.