BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

ELECTROMAGNETIC CHUCKSModel KESL LATERAL FINE PITCH ELECTROMAGNETIC CHUCKELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKSCONTROLLERS MAGNETIC CHUCKS ELECTROMAGNETIC CHUCKSKESL-1535A-1Chuck controllerrequired additionallyPitches for comparison[Application]These are versatile electromagnetic chucks with poles in the longitudinal directioncapable of holding workpieces, thin and thick, in grinding and light duty cutting. Inparticular, these chucks are suitable for grinding and light duty cutting of long thinworkpieces and buff and belt grinding of large quantities of workpieces, which are difficultto hold by standard type electromagnetic chucks.[Features]●A fine pole pattern is arranged in the longitudinal direction.●The N-S magnetic force lines are spaced relatively wide for good holding via a belt. (Note,however, that because the distribution of the holding power is not uniform, this model maynot be suitable for grinding small workpieces arranged over the whole surface.)●Powerful holding, but low height.Power Cord 2?3m8L 1P8BeB 2tB 1HBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSL 2[mm(in)]ModelNominal SizeWork Face Pole Pitch Mounting Face Height PowerElectroVoltage Current MassB? L? t Be P B? L? h HCordChuck MasterKESL-1025A-1100(3.93)×250(9.84)100(3.93)250(9.84)77(3.03)98(3.85)250(9.84)0.36A12kg/ 26 lbKESL-1325A-1125(4.92)×250(9.84)125(4.92)101(3.97)123(4.84)0.26A14kg/ 31 lbKESL-1530A-1150(5.90)×300(11.8)300(11.8)300(11.8)0.48A2m19kg/ 42 lbES-M103BKESL-1535A-1150(5.90)×350(13.7)150(5.90) 350(13.7)20125(4.92)148(5.82)350(13.7)700.61A(78.7) 23kg/ 51 lbES-M305B(0.78)4(1+3)13(2.75)EH-V305AKESL-1545A-1 150(5.90)×450(17.7) 450(17.7) 450(17.7) 0.85A 29kg/ 64 lb90 VDCEH-VE305AKESL-2040A-1 200(7.87)×400(15.7)400(15.7)(0.15)400(15.7) (0.51)1.08A 34kg/ 75 lbKESL-2050A-1200(7.87)×500(19.6)200(7.87) 500(19.6)173(6.81)198(7.79)500(19.6)1.50A42kg/ 93 lbKESL-2060A-1200(7.87)×600(23.6)600(23.6)600(23.6)1.60A3m51kg/113 lbP17?P20KESL-2550A-1250(9.84)×500(19.6)250(9.84) 500(19.6)27225(8.85)248(9.76)500(19.6)851.64A(118) 62kg/137 lbKESL-3060A-1300(11.8)×600(23.6)300(11.8) 600(23.6) (1.06) 273(10.7)298(11.7)600(23.6)(3.34)1.70A98kg/216 lb※If the magnetic force needs not be adjusted, use ES-M.※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.Model KETW-N ELECTROMAGNETIC MICROPITCH CHUCKEnvironmentallyfriendly[Application]Suitable for grinding and cutting of thin workpieces. However, workpieces shouldhave an attractive face longer than 80 mm in the longitudinal direction.[Features]●In addition to grinding of thin workpieces that meet the above conditions,this model is also suitable for cutting.●A resin-bonded structural face plate having little environmental burden isemployed.Side stopperhPower cordHOLDINGTOOLSMEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS9KETW-N1530Chuck controller required additionally〈Information〉For small and thin workpieces, the permanent magneticmicropitch chuck is recommended. See Model RMWH.Work FacePole Mounting Face Height MountingModel Nominal SizeVoltage CurrentPitchHolePowerMassB? L? t Le B? L? h HCordKETW-N1530 150(5.90)×300(11.8)300(11.8) 245(9.64)314(12.3)0.4A31kg/ 68 lb19146100KETW-N1535 150(5.90)×350(13.7) 150(5.90) 350(13.7) 293(11.5) 364(14.3) 0.45A(0.75)(5.74)(3.93)2m 36kg/ 79 lbKETW-N1545 150(5.90)×450(17.7) 450(17.7) 397(15.6) 464(18.2) 0.62A (78.7) 46kg/101 lbKETW-N2040 200(7.87)×400(15.7)400(15.7) 349(13.7) 4(0.8+3.2)414(16.3) 200.7A 65kg/144 lbClamping 90 VDC200(7.87)(0.15)196KETW-N2050 200(7.87)×500(19.6) 500(19.6) 445(17.5) 514(20.2) (0.78)0.8A82kg/180 lb25(7.71)120KETW-N2060 200(7.87)×600(23.6)0.92A(0.98)(4.72)3m 98kg/216 lb614KETW-N2560 250(9.84)×600(23.6) 250(9.84) 600(23.6) 549(21.6)246(9.68) 1.2A (118) 123kg/271 lb(24.1)P17?P20KETW-N3060 300(11.8)×600(23.6) 300(11.8) 296(11.4) 1.56A 147kg/324 lb※If the magnetic force needs not be adjusted, use ES-M.※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.※Only the side stopper is included. (The back stopper is not included.)B 1B 2HthL 1LeL 2ElectroChuck MasterES-M103BES-M305BEH-V305AEH-VE305A[mm(in)]Remarks※For types with acombination of arectifier anddemagnetizer, seepages of“ChuckControllers.”