BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

2PERMANENT ELECTROMAGNETIC CHUCKSELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKSELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSModel EP-Q PERMANENT ELECTROMAGNETIC CHUCK FOR CUTTINGA Line-up of products selectable according to machining methods and workpieces.■Considerable power saving and reduction in size of the Chuck Master by the renewed design.■The detachable connector type is employed to respond to pallet changing.■Electricity is used only when mounting and demounting workpieces. Workpieces can be held firmly in the event of power failure.■Usable in wet machining operations.[Application]Suitable for securing workpieces during cutting on milling machines and machining centers.[Features]●The power cord is of detachable connector type for easy use. Theconnector cap is of waterproof type.●Can be used in wet machining operations.●The chuck is very thin, 70 mm in height, and light weight.●Less accuracy change and highly rigid construction.●Considerable power saving compared with conventional products.(□70: 50% reduction,□50: 70% reduction)■EP-QN Series■EP-QS SeriesEP-QN7-50100APowersavingMinimalheatgenerationChuck controller required additionallyAn example of machining by use of straightening block●Magnetization and demagnetization in a very short time.●Tapped holes on the attractive face can be used to install various blocks tohold workpieces by various methods according to machining operations.●Straightening blocks are also available that are mounted on the chuck workface to hold workpieces by an induction field. These optional products arevery useful for workpieces having irregular attractive faces that for examplehave steps and distortion and for machining the bottom and side faces ofworkpieces. (See■Options on page 32.)WWe70PWN -M±120PL 2Le10LConnector cable: 5 mEnvironmentallyfriendlyL 1[mm(in)]StandardWork Face Pole Dimensions Mounting Face Tapped Hole on Attractive FaceApplicableMassSize ModelW L We Le No. of poles P W? L? L? N MChuck Master3060A 300(11.8) 610(24.0) 252(9.92) 570(22.4) 2418(0.70) 16(0.63) 630(24.8) 2490kg/198 lb4080A 420(16.5) 800(31.5) 372(14.6) 760(29.9) 40 28(1.10) 25(0.98) 820(32.2) 40 160kg/352 lbEP-QN550(1.96)8(0.31)EPS-P2100B50100A 500(19.6) 432(17.0) 60 18(0.70) 60 230kg/507 lb960(37.8) 917(36.1)26(1.02) 980(38.5)60100A 600(23.6) 552(21.7) 72 24(0.94) 72 280kg/617 lb4080A 390(15.3) 800(31.5) 332(13.0) 760(29.9) 2424(0.94) 820(32.2) 24150kg/330 lb EPS-P2100BEP-QN7 50100A 500(19.6) 452(17.8) 40 70(2.75) 28(1.10)40 10(0.39) 240kg/529 lb1000(39.4) 960(37.8)25(0.98) 1020(40.1)EPS-P2100B-260100A 620(24.4) 572(22.5) 50 50 300kg/661 lb※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.LeConnector cable: 5 mP L 2 10PMEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS31EP-QS5-3060APowersavingMinimalheatgenerationChuck controller required additionallyWWe7010N -M±120LL 1EnvironmentallyfriendlyStandardWork Face Pole Dimensions Mounting Face Tapped Hole on Attractive FaceMassSize ModelW L We Le No. of poles P L? L? N M3060A 300(11.8) 610(24.0) 252(9.92) 570(22.4) 3216(0.55) 630(24.8) 3290kg/198 lb4080A 420(16.5) 800(31.5) 372(14.6) 760(29.9) 60 25(0.98) 820(32.2) 60 160kg/352 lbEP-QS550(1.96)8(0.31)50100A 500(19.6) 432(17.0) 8484 230kg/507 lb960(37.8) 917(36.1)26(1.02) 980(38.5)60100A 600(23.6) 552(21.7) 108 108 280kg/617 lb3060A 300(11.8) 600(23.6) 252(9.92) 562(22.1) 1825(0.98) 620(24.4) 1886kg/189 lb4080A 390(15.3) 800(31.5) 332(13.0) 760(29.9) 32 24(0.94) 820(32.2) 32 150kg/330 lbEP-QS770(2.75)10(0.39)50100A 470(18.5) 412(16.2) 5050 220kg/485 lb1000(39.4) 960(37.8)25(0.98) 1020(40.1)60100A 620(24.4) 572(22.5) 70 70 300kg/661 lb※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.[mm(in)]ApplicableChuck MasterEPS-P2100BEPS-P2100B-2EPS-P2100BEPS-P2100B-2