BookTitleMAGNET_GENERAL_CATALOG_2019

page
40/188

This page is an overview of MAGNET_GENERAL_CATALOG_2019 on page40
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.

MAGNET_GENERAL_CATALOG_2019

ReadBook

Open e-Book in Flash Viewer

This e-Book is not available in your environment.

Summary

MAGNET_GENERAL_CATALOG_2019

PERMANENT ELECTROMAGNETIC CHUCKSELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKSELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSMEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS33Model EP-QS3 RECTANGULAR PERMANENT ELECTROMAGNETIC CHUCKVery small magnetic pole type suitable for small and thin workpieces!EnvironmentallyfriendlyModelModel EPZF-WX PERMANENT ELECTROMAGNETIC CHUCK ACSHIM*A new construction to preventoccurrence of stick motionfailure due to chips employed.Work Face Pole Dimensions Mounting Face HeightW L We Le No.of Poles P W L? HEP-QS3-1732A 165(6.49) 315(23.6) 125(4.92) 245(9.64) 18165(6.49) 335(13.1)EP-QS3-2040A205(8.07)400(15.7)165(6.49)325(12.7)3235205(8.07)420(16.5)45(1.77)26kg/ 57 lbEP-QS3-3060A295(11.6)600(23.6)245(9.64)525(20.6)78(1.37)295(11.6)620(24.4)56kg/123 lbMass16kg/ 35 lbHighly precise straighteningoperations realized!Electro ChuckMasterEPS-P2100BEP-QS3-4282A 415(16.3) 820(32.2) 365(14.3) 745(29.3) 162 415(16.3) 840(33.0) 50(1.96) 120kg/264 lb EPS-P2100B-2※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.EnvironmentallyfriendlyPowersavingPowersavingMinimalheatgenerationMinimalheatgenerationEPZF-WX4280(An example of special fabrication)Chuck controllerrequired additionallyEP-QS3-3060APatended・Design registeredChuck controllerrequired additionallyModelNominal SizeWork Face Mounting Face Height Numberof Sticks VoltageB L B L? t HEPZF-WX50100500(19.6)×500500401000(39.3) (19.6) 1000 (19.6) 1020 30 150180EPZF-WX60100600(23.6)×600 (39.3) 600 (40.1)(1.18)(5.90)VDC481000(39.3) (23.6) (23.6)MassSinglestopper[mm(in)]DedicatedControl Unit520kg/1146 lbEPS-WF275A620kg/1367 lb※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations arerepeated frequently, the chucks may be damaged by overheat.[mm(in)]Rated OutputDimensionsOperation boxModel Power SourceMassVoltage Current Width Depth Height Width Depth HeightSingle-phase 30 VDC ? 180 VDC Low magnetic 1300 400 900 190kg/ 200 70 180EPS-WF275A75A200 VAC 50/60Hz force:±30 VDC (Continuous) (51.1)(15.7)(35.4)418 lb (7.87)(2.75)(7.08)[Application]Used for securing workpieces during cutting by milling machines, machining centers, etc.[Features]●Compared with conventional permanent electromagnetic chucks for cutting, thistype has higher holding power on small and thin workpieces.●Compared with conventional chucks, the residual holding power has been reducedto a third maximum.●An original construction is employed to keep the height below 50 mm, thusrealizing thin and light weight chucks.●Electricity is supplied momentarily only when mounting and demountingworkpieces, thus minimal heat is generated and highly precise machining can beexpected. Also electricity is saved.●Can be used in wet operations.●The employment of a quick connector facilitates connection/removal of the cable.Holding power-thickness characteristic(Test piece:□50×T25, S15C)Holding power【N】35003000250020001500EP-Q□35EP-Q□701000EP-Q□50KETN-1530A500EP-DWM00 5 10 15 20 25Thickness【mm】SingleStopper(2 faces)[mm(in)][Application]Most suitable for precise setting of workpieces including mold bases in the millingsector.[Features]●The sticks on the chuck attractive face hold workpieces in the natural state.●The number of sticks can be increased/decreased according to workpieces.●Electricity is supplied momentarily only when mounting and demountingworkpieces, thus minimal heat is generated and highly precise machining can beexpected. Also electricity is saved. In addition, this ACSHIM can be used notonly for plate machining, but also for various machining operations that requireworkpieces to be held for a long time.●The elimination of the lid of the stick section facilitates maintenance as there isno need to align the level of the body and the lid when replacing the stick unit.●The utilization of T slots enables it to clamp nonferrous or irregular shapedworkpieces.●The low magnetic force control by the dedicated control unit (EPS-WF275A)offers a low attraction function.●Can be used in wet operations.HydraulichoseAir tubePowercordProtectivecoverWork supportN pieces