BookTitleMAGNET_GENERAL_CATALOG_2019

page
42/188

This page is an overview of MAGNET_GENERAL_CATALOG_2019 on page42
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.

MAGNET_GENERAL_CATALOG_2019

ReadBook

Open e-Book in Flash Viewer

This e-Book is not available in your environment.

Summary

MAGNET_GENERAL_CATALOG_2019

PERMANENT ELECTROMAGNETIC CHUCKSModel EP-QZ SUPER POWERFUL PERMANENT ELECTROMAGNETIC CHUCK FOR LONG WORKPIECEELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKSELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMEnvironmentallyfriendlyChuck controllerrequired additionallyChuck controllerrequired additionally[Features]●The gap characteristic is superior to that of the current Model EP-QN/QS. These chucks are suitable for workpieces that have poor flatnessand require large holding power.●These chucks replace conventional hydraulic and mechanicalclamping to reduce the setup time and improve productivity.●The magnetic poles are arranged according to shapes and length ofworkpieces such as rails. Securing blocks specially designedaccording to workpiece shapes are also available.●A type with a separator made of brass is also available.EP-QZ8-1550AAn example of special fabrication[mm(in)]ModelMax. Holding Power per PolePole SizeNo. of PolesFeaturesElectro Chuck MasterEP-QZ8-15100A□75(□2.95) 750kgf□75(□2.95)5Single typeEPS-P2100BEP-QZW-30100A□50(□1.96) 300kgf□75(2.95)+□50(1.96)10(□75)+14(□50)Double typeEPS-P2100B-2※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.Model EP-D DEMAGNETIZING FUNCTION-EQUIPPED PERMANENT ELECTROMAGNETIC CHUCK FOR CUTTINGStrong holding power and good release performance realized!EnvironmentallyfriendlyPowersavingMinimalheatgeneration[Application]Used for securing workpieces during cutting by milling machines,machining centers, etc.[Features]●A coil dedicated to demagnetization has significantly improved theworkpiece release performance when the chuck is turned off.●The magnetic pole arrangement to concentrate magnetism on theworkpiece provides strong holding power.●Hardened steel and special steel workpieces having large residualmagnetism can be released quicker than the conventional chucks.●Electricity is used only when mounting and demounting workpieces,thus minimal heat is generated and electricity is saved.●Can be used in wet operations.SINE BARCHUCKSEP-D3060[mm(in)]BLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSMEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS35ModelEP-D 3060EP-D 4080EP-D50100EP-D60100Holding power【KN】302520151050Work Face Dimensions Mounting FaceW L We Le W? W2 L?304 618 264 558(11.9)(24.3)(10.3)(21.9) 404 786 364 726(15.9)(30.9)(14.3)(28.5) 504(19.8) 1038(40.8)604(23.7)464(18.2) 978(38.5)564(22.2)Mass240(9.44) 232(9.13) 638(25.1) 110kg/242 lb340(13.3) 332(13.0) 806(31.7) 185kg/407 lb440(17.3) 432(17.0)305kg/672 lb1058(41.6)540(21.2) 532(20.9) 360kg/793 lbComparison of holding powerHolding power(□160×t50)EP-DEP-QS7600500400300200100Electro ChuckMasterEPS-D2100AEPS-D2100A-2※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeatedfrequently, the chucks may be damaged by overheat.WWe8520±11W1230W2LeLL 1Comparison of residual holding powerResidual holding power(□160×t50)0SS400 S50C SUS420J2 SS400 S50C SUS420J2Residual holding power【N】EP-DEP-QS7