BookTitleMAGNET_GENERAL_CATALOG_2019

page
44/188

This page is an overview of MAGNET_GENERAL_CATALOG_2019 on page44
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.

MAGNET_GENERAL_CATALOG_2019

ReadBook

Open e-Book in Flash Viewer

This e-Book is not available in your environment.

Summary

MAGNET_GENERAL_CATALOG_2019

PERMANENT ELECTROMAGNETIC CHUCKSModel EPT/EPT-LW PERMANENT ELECTROMAGNETIC CHUCK (STANDARD/LOW MAGNETIC FORCE CONTROL)ELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKSELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSMEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS37EnvironmentallyfriendlyBH[Application]Suitable for high precision grinding and slicing.[Features]●Since electricity is supplied momentarily only to control the magnetomotive forcewhen mounting/demounting a workpiece, little heat is generated internally toenable highly precise machining.●Since electricity needs not be supplied continuously even while holding aworkpiece, the running cost is very low.●Since the holding power is maintained by the permanent magnet, safety is securedin the event of power failure and cable breakage.●A resin-bonded structural face plate having little environmental burden is employed.Side stopper Back stopper Power cordAbout EPT-LWModel EPT-LW is equipped with a low magneticforce (weak attraction) control function that isdifficult with conventional permanent electromagneticchucks and therefore facilitates strain relieving andworkpiece positioning at the same level asPLelectromagnetic chucks. (When the low magneticLeforce control is active, the power is suppliedcontinuously.)EPT-3060FL 2 10NOTE:The L2 dimension has not been machinedPlease note that a dedicated Chuck Master (ModelEPH-LW) (see page 39) needs to be used together.together with L and therefore, there maybe some variation.[mm(in)]ModelWork Face Pole Pitch Mounting Face Height Voltage Current PowerNominal SizeCordMassElectro Chuck MasterStandard Low mag. force control B L Le t P L? h H Standard Low mag. force control Standard Low mag. force control Standard Low mag. force controlEPT- 1530F EPT-LW 1530F 150(5.90)×300(11.8)300 24030024kg/1.91A 0.80A(11.8)(9.44)(11.8)52 lb150 350 2963502m 28kg/EPT- 1535F EPT-LW 1535F 150(5.90)×350(13.7)2.43A 0.93A(5.90)(13.7)(11.6)(13.7)(78.7) 61 lbEPT- 1545F EPT-LW 1545F 150(5.90)×450(17.7)14(2+12)450 380 20.54508036kg/0.552.64A 1.17A(17.7)(14.9)(0.80)(17.7) (3.15)79 lbEPH-LW205B(0.07+0.47)EPH-LWE205B500 43650053kg/EPT- 2050F EPT-LW 2050F 200(7.87)×500(19.6) 5.88A 3.31A200 (19.6)(17.1)(19.6)116 lb(7.87) 5483m 65kg/EPT- 2060F EPT-LW 2060F 200(7.87)×600(23.6)7.87A 3.82A600(21.5) 600 2090 180(118) 143 lbEPS-215B(23.6)(23.6)(0.78)VDC VDCEPT- 3060F EPT-LW 3060F 300(11.8)×600(23.6) 300529140kg/6.14A 2.55A(11.8) (20.8)308 lb800 724800211kg/EPT- 4080F EPT-LW 4080F 400(15.7)×800(31.5) 11.0A 6.59A400 (31.5)(28.5)(31.5)465 lb(15.7)19.5(2.5+17)1000 919 25.01000 100EPT-40100F EPT-LW40100F 400(15.7)×1000(39.4)0.7612.5A 6.45A(39.4)(36.1)(0.98)(39.4) (3.93)(0.09+0.66)5m 265kg/800 724800(196) 584 lbEPT- 5080F EPT-LW 5080F 500(19.6)×800(31.5) 9.01A 5.41A500 (31.5)(28.5)(31.5)EPH-LWE210B(19.6) 1000 919EPT-50100F EPT-LW50100F 500(19.6)×1000(39.4)(39.4)(36.1)th1000(39.4)11.7A 6.00A※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.Model EPT-H POWERFUL PERMANENT ELECTROMAGNETIC CHUCKEnvironmentallyfriendlyPowersavingPowersavingMinimalheatgenerationMinimalheatgenerationChuck controllerrequired additionallyChuck controllerrequired additionallyEPT-H3060F(An example of special fabrication)BHthSide stopper Back stopper Power cordPLLeL 210NOTE:The L2 dimension has not been machinedtogether with L and therefore, there maybe some variation.[mm(in)]ModelNominal SizeWork Face Pole Pitch Mounting Face HeightPowerElectroVoltageMassB L Le t P L? h HCordChuck MasterEPT-H1530F150(5.90)×300(11.8)150(5.90) 300(11.8)240(9.44)14(2+12)300(11.8)2m(78.7) 30kg/ 66.1 lbEPT-H2050F200(7.87)×500(19.6)200(7.87) 500(19.6)436(17.1)0.55(0.07+0.47)500(19.6)83kg/ 183 lbEPT-H3060F300(11.8)×600(23.6)300(11.8) 600(23.6)3020 1003m(118)529(20.8)600(23.6) 180 VDC142kg/ 313 lb(1.18) 19.5(2.5+17)(0.78) (3.93)EPS-W215BEPT-H4080F 400(15.7)×800(31.5) 400(15.7) 800(31.5) 724(28.5) 0.76 800(31.5)215kg/ 474 lb(0.09+0.66)5m(196)EPT-H50100F 500(19.6)×1000(39.4) 500(19.6) 1000(39.4) 919(36.1) 1000(39.4) 335kg/ 738 lb※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.330kg/727 lb[Application]Suitable for high precision grinding andslicing.[Features]●Compared with the standard type (EPT),these chucks generate a larger magneticforce and therefore are capable of securingworkpieces firmly during grinding of largemachining load.●A resin-bonded structural face plate havinglittle environmental burden is employed.