BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

BLOCKS FOR MCEPB / EPB-2F / RMA-2FModel EPB PERMANENT ELECTROMAGNETIC BLOCKEnvironmentallyfriendlyEPB-1F1625AModelEPB-1F1625AEPB-1F2525AEPB-1F3333APowersavingDimensionsW L HPoleSize160(6.29)250250(9.84)15070(9.84)(5.90)(2.75)330 330(12.9) (12.9)Chuck controllerrequired additionallyEPB-1F2525ANo.ofPolesHoldingPowerMass2 11.8kN 40kg/ 88 lb4 23.5kN 60kg/132 lb9 53kN 120kg/264 lb[Application]Designed for holding workpieces on such machines as machining centers and NCmachine tools. Most suitable for machining workpieces by 5-face machining centers, etc.[Features]●By securing a workpiece overhanging, the setup time on the 5-face machiningcenter can be shortened.●These blocks can be used in wet operations and therefore can be used likenormal magnetic chucks.●Since these blocks are of permanent electromagnetic type, the holding power isnot affected by power failure or cable breakage. Also since very little heat isgenerated, thermal influence on workpiece is minimal.●The metal connector design facilitates disconnection of the power cable. (Palletchange and external setup facilitated.)L[mm(in)]ElectroChuck MasterEPS-P2100B※The chuck controller is not included.※Turning the permanent electromagnetic blocks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the blocks may be damaged by overheat.※The holding power is based on a test piece of SS400, 50 mm thick, ground surface held on the whole face.EnvironmentallyfriendlyPowersavingMinimalheatgenerationMinimalheatgenerationChuck controllerrequired additionallyAn example of usageModel EPB-2F DOUBLE-FACE HOLDING PERMANENT ELECTROMAGNETIC BLOCKEPB-2F2525WHL[Application]Suitable for various cutting applications such as by the MC.[Features]●As a workpiece is held on both faces, no mechanical clamping isnecessary. It can be set on the machine table easily.●By securing a workpiece overhanging, five faces can be machined inone chucking to improve the machining efficiency and accuracy.●Since these blocks are of permanent electromagnetic type, the holdingpower is not affected by power failure or cable breakage. Also sincevery little heat is generated, thermal influence on workpiece isminimal.●The power cable is of metal connector type that can be disconnectedeasily to make it suitable for pallet change and external setup.●Several blocks can be used at the same time according to workpiecesizes and machining conditions.[mm(in)]ModelDimensionsNo. of PolesHoldingPole SizeW L H(per Face)PowerMassEPB-2F2525250(9.84)250(9.84)423.6kN40kg/ 88 lbEPB-2F3333330(12.9)330(12.9)100(3.93)70(2.75)953.0kN70kg/154 lbWH8525 (40)20ElectroChuck MasterEPS-P2100B※The chuck controller is not included.※Turning the permanent electromagnetic blocks on and off must be limited to once per several minutes. If on/ off operations are repeated frequently, the blocksmay be damaged by overheat.※The holding power is based on a test piece of SS400, 50 mm thick, ground surface held on the whole face.ELECTROMAGNETICCHUCKSCHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSModel RMA-2F POWERFUL DOUBLE-FACE HOLDING PERMANENT MAGNETIC BLOCKRMA-2F1530[Application]Suitable for various cutting applications such as by the MC.[Features]●Since no mechanical clamping is required, setting on the machine table can be done easily toshorten the setup time.●By securing a workpiece overhanging, five faces can be machined in one chucking.●These blocks can be used in wet operations.●These blocks are of permanent magnetic type that requires no power source. No troublesomework such as electrical connection is required and there is no fear of electrical troubles such aspower failure and cable breakage.Single stopper[mm(in)]BHOLDINGTOOLSMEASURINGTOOL HOLDERSMAGNETICHOLDERSModelDimensionsB L H LeHoldingPowerRMA-2F1325 125(4.92) 250(9.84)184(7.24) 10kN 23kg/ 51 lb96(3.77)RMA-2F1530 150(5.90) 300(11.8) 229(9.01) 15kN 33kg/ 72 lbRMA-2F2040 200(7.87) 400(15.7) 100(3.93) 334(13.1) 30kN 62kg/137 lb※The holding power is based on a test piece of SS400, 50 mm thick, ground surface held on the whole face.MassHRatchet handleLLe(P=4+11)23MAGNETICTOOLS42