BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

SINE BAR CHUCKSSBE-UTypes of Sine Bar ChucksThe sine bar chucks are used to set accurate angles ofworkpieces for highly precise grinding or as an inspection fixture.This is a type of chuck that utilizes angle setting by a sine barand the chuck work face can be set to a desired angle efficiently.■FeatureThe sine bar chucks come in various types such as electromagnetic, water-cooled, permanent electromagnetic, permanentmagnetic and in various sizes.Type Model Features RemarksTilt electromagnetic SBE-U Dust cover provided on gauge blockTilt water-cooled electromagnetic SBC-U High precision water-cooled typeTilt permanent electromagnetic SBEP-UMomentary power application for minimizedheat generationTilt permanent magnetic SBP-U Dust cover provided on gauge blockSine bar chuck compound type SBP-R・LS Thin compound typeSine bar chuck single typeSBP-R・SSBP-R・LThin single typeTilting in longitudinal direction※The rotary tilting sine bar chuck comes with a gauge block (for 0°setting) of 25.882 mm of JIS Class B.SBE-USBP-R・LSSBP-R・LSBP-R713ELECTROMAGNETICCHUCKSCHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSVACUUMCHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCGauge block setting location on the right side(photo): R type, and on the left side: L type.The lock lever is installed on both sides.Model SBE-U TILT TYPE ELECTROMAGNETIC SINE BAR CHUCKPROMELTA*SYSTEMSINE BARCHUCKSEnvironmentallyfriendlyChuck controller required additionallyPower cordBLOCKS, HOLDERS,MINI CHUCKSSBE-1131UFR-C[Application]Suitable for high precision angle grinding of molds and jigs.[Features]●The gauge block can be set on either the right side (R) or left side (L) to meet therotating direction of the grinding wheel of the grinder.●The chuck can be smoothly tilted and easily operated.●An angle can be set finely by one try with the clamp system.●The position can be changed and secured by pulling the lever in the axial direction.●When the dustproof cover of the gauge block is opened beyond about 60 degrees, it islocked to facilitate setup and cleaning.●A resin-bonded structural face plate having little environmental burden is employed.ModelSBE-1131UFR-CSBE-1131UFL-CNominalSize110(4.33)×315(12.4)Work Face Pole Pitch MountingLengthB? L? Le H? P L?Angle 0°,Min.HeightCover fullyopen, Max.11(3+8)110 315 278 113492 138 2100.43(4.33)(12.4)(10.9)(4.44)(19.3) (5.43) (8.26)(0.11+0.31)TiltAngleP515.5L125 32L2AngleElectroVoltage Current MassAccuracy Chuck Masterー15°? 0.007/10090 VDC 0.3A+45°max.84Le90H136kg/79 lbES-M103BES-M305BEH-V305A8013815°45°R2025.882Remarks100165B114110[mm(in)]※?For types with a combination ofa rectifier and demagnetizer, seepages of“Chuck Controllers.”P17?P20※The type having the gauge block setting area on the right side is indicated by“R”and that on the left side indicated by“L”.※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.※A gauge block (25.882 mm) for 0°is included. For the mechanism of angle setting, see the bottom part on page 51. The conversion table included with the product facilitates angle setting.HOLDINGTOOLSMEASURINGTOOL HOLDERSMAGNETICHOLDERSMAGNETICTOOLS48