BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

SINE BAR CHUCKSModel SBC-U TILT TYPE WATER-COOLED ELECTROMAGNETIC SINE BAR CHUCKELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKS ELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSSBC-1131UFL-C[Application]Constructed to enable real-time internal cooling of heat generated when power is applied tothe electromagnet, making these chucks suitable for higher precision grinding operation.[Features]●Change in accuracy is minimized by supplying coolant at a flow rate of 2 to 4 L/min tominimize coil heating.●The mechanical functions and features are almost the same as those of Model SBE chucks.●A resin-bonded structural face plate having little environmental burden is employed.ModelNominalSizeWork Face Pole Pitch MountingLengthB? L? Le H? P L?SBC-1131UFR-C 11(3+8)110(4.33)×110 315 278 1134920.43315(12.4) (4.33)(12.4)(10.9)(4.44)(19.3)SBC-1131UFL-C(0.11+0.31)Chuck controller required additionallyModel SBEP-U TILT TYPE PERMANENT ELECTROMAGNETIC SINE BAR CHUCKP515.5L125 32※The type having the gauge block setting area on the right side is indicated by“R”and that on the left side indicated by“L”.※A cooler unit is required additionally.※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.※A gauge block (25.882 mm) for 0°is included. For the mechanism of angle setting, see the bottom part on page 51. The conversion table included with the product facilitates angle setting.SBEP-1131UFR-CL284Le90H1Power cord8013815°45°R2025.882100110B114165[mm(in)]Chuck controller required additionally[Application]These chucks are recommended for angle grinding of molds and jigs. Sincemagnetization is carried out by momentary power application, almost no heat isgenerated to make this model suitable for high precision grinding.25 32L2[Features]●Electricity is applied momentarily. No electricity is required to maintain the holding power during grinding, thus saving energy.●The holding power is maintained in the event of power failure during grinding, thus enhancing safety.●The mechanical functions and features are almost the same as those of Model SBE.●A resin-bonded structural face plate having little environmental burden is employed.ModelNominalSizeWork FacePole PitchAngle 0°,Min.Height138(5.43)MountingLengthB? L? Le H? P L?SBEP-1131UFR-C 110(4.33) 110 315 278 113 11(3+8) 492SBEP-1131UFL-C×315(12.4)(4.33)(12.4)(10.9)(4.44)0.43(0.11+0.31) (19.3)EnvironmentallyfriendlyWatercooledCover fullyopen, Max.TiltAngle210ー15°?(8.26) +45°EnvironmentallyfriendlyPowersavingAngle 0°,Min.138(5.43)AngleVoltageAccuracyCurrentMass0.007/10090 VDC 0.3Amax.P515.5L136kg/79 lb84Le90H1ElectroChuckMasterES-M103BES-M305BEH-V305A(7)80Power cord13815°Remarks※For models with a combinationof a rectifier and demagnetizer,see pages of“Chuck Controllers.”※The type having the gauge block setting area on the right side is indicated by“R”and that on the left side indicated by“L”.※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.※A gauge block (25.882 mm) for 0°is included. For the mechanism of angle setting, see the bottom part on page 51. The conversion table included with the product facilitates angle setting.HeightCover fullyopen, Max.210(8.26)Tilt AngleAngleAccuracyー15°?+45°0.007/100max.Voltage Current Mass45°R2025.882P17?P20100165110B114[mm(in)]ElectroChuck Master90 VDC 2.1A 36kg/79 lb EPS-215BModel SBP-R.UR TILT TYPE PERMANENT MAGNETIC SINE BAR CHUCKMEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS49SBP-R1130UR-B[Application]Suitable for grinding molds and jigs including relatively small and thin ones that requirehigh precision.[Features]●No electricity is needed, thus no heat is generated.●The mechanical functions and features are almost the same as those of Model SBE.Work Face Pole Pitch Mounting Face HeightModelNominal SizeB? L? Le P B? L? HSBP-R1130UR-B 105(4.13)×300(11.8) 105(4.13)300(11.8)256(10.0)3(1+2)0.11(0.03+0.07)110(4.33)477(18.7)PL1Le959010Φ25 25135(5.31)L2880H15°45°25.882R128Back stopper※A gauge block (25.882 mm) for 0°is included. For the mechanism of angle setting, see the bottom part on page 51. The conversion table included with the product facilitates angle setting.10016514B2B1[mm(in)]Height at Max. Tilt Tilt Angle Angle Accuracy Mass210(8.26)ー15°?+45°0.007/100 max. 35kg/77 lb