BookTitleMAGNET_GENERAL_CATALOG_2019

page
61/188

This page is an overview of MAGNET_GENERAL_CATALOG_2019 on page61
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.

MAGNET_GENERAL_CATALOG_2019

ReadBook

Open e-Book in Flash Viewer

This e-Book is not available in your environment.

Summary

MAGNET_GENERAL_CATALOG_2019

tRMAW-2F / KPB / KM-JB / MMModel KM-JB SWITCHABLE PERMANENT MAGNETIC HOLDERSuitable as exclusive fixing jig for round steel bars and irregularly shaped workpieces!Additional workallowed area.(Top/bottom/right/left)Additionally workable up to10 mm on each face.????KM-JB0709※However, avoid making a holein the pin and counterbore areas.KM-JB side faceKM-JB0812PinCounterbore[Application]In addition to using these holders as a fixing jig for small workpieces, they canbe used as a block to support 3 points of a workpiece during grinding.[Features]●Each face can be worked additionally for up to 10mm. (The on/off operationface and rear face are excluded.)●By using these holders as exclusive jigs for a particular workpiece, the workefficiency is improved.●As these holders are of drip-proof construction, they can be used in liquidsuch as during electric discharge machining.Hindicates the attractive face.BFOFKANETCEON835[mm(in)]ModelHoldingDimensionsPowerB L HMassKM-JB0709392N(40kgf)65(2.55)85(3.34)70(2.75)2.5kg/ 5.5 lbKM-JB0812883N(90kgf)80(3.14)120(4.72)90(3.54)5.5kg/12.1 lb※The holding power is based on a test piece of□50×t25, S15C.※A hex wrench key is included.LELECTROMAGNETICCHUCKSCHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCModel MM FREE BLOCKFreely workable permanent magnetic blockMM2F-512MM3F-612[Application]These blocks are designed to allow deep engraving such asgrooves and steps on the attractive face to fit workpiece shapeswhen holding workpieces.[Features]●The attractive face can be removed up to 10 mm deep from thesurface of the new block.●As workpieces can be fitted in grooves, a large machiningpressure can be used. Also cemented carbide workpieces,which are difficult to hold by a magnetic chuck, can be securedby using these blocks to enable grinding.●These blocks can be mounted on the magnetic chuck work face.●There are two types; a magnetic force ON-OFF type and a typenot equipped with an ON-OFF function.〈MM2F-512〉LVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSMM3F-912MM3Y-1023Nominal HoldingDimensions Pole Pitch Work Allowance Mag. ForceModelMassSize Power B L H B? H? P t ON/OFF50(1.96)×200N 50MM2F- 512120(4.72) (20kgf)(1.96)40120 50 (1.57) 8(3+5)400.31(4.72)(1.96)(1.57)(0.11+0.19)※The holding power is a reference value obtained using a test piece of S15C,□50×t25, ground surface.※For MM3Y-1023, a dedicated handle is included.※Note that when workpieces are held on two or more faces simultaneously, the holding power of each face drops.Max.102kg/4.4 lb60(2.36)×400N 60Not 2.5kg/MM3F- 612120(4.72) (40kgf)(2.36)provided 5.5 lb90(3.54)×600N 9070(0.39)3.5kg/MM3F- 912120(4.72) (60kgf)(3.54)(2.75)7.7 lbMM3Y-1023 100(3.93)×[mm(in)]750N 100 230 100 80 90 15.220kg/Provided230(9.05) (75kgf)(3.93)(9.05)(3.93)(3.15)(3.54)(0.59)44 lbtB 1BHHtH1B 1BtB 1tB〈MM3Y-1023〉tPtH11HH10ON50tp2 attractive faces〈MM3F-612ー912〉LL204250300p3 attractive facesindicates the attractive face.HOLDINGTOOLSMEASURINGTOOL HOLDERSMAGNETICHOLDERSMAGNETICTOOLS54