BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

Model KMV-M PERMANENT MAGNETIC MINI V-BLOCKKVS / KMV / KMV-M / KT . KTVKMV-M032■KMV-M accuracyItemModel・AccuracyBottom face to top faceKMV-M020 KMV-M025 KMV-M032Bottom face to V faceParallelismSide face to side face101010Side face to V faceEnd face to end faceFlatness of bottom face555Bottom face to side faceSquarenessBottom face to end face212121End face to V faceDifference in height between V face and topface of one set of blocks※If you require higher accuracy, please contact us.ModelHolding Power7 7 7ApplicableDiameterKMV-M025[Application]These blocks are used to hold small-diameter round bars on optical measuringequipment. (Non-watertight type)[Features]●One set consists of two blocks. The attractive faces and other work faces havebeen finished precisely. The blocks can be turned ON and OFF by 90°turning usinga screwdriver on the bottom face.※The holding power is based onφ10 round steel bar.■The dimensional accuracy of KMV-M is based on KANETEC in-house standards. If you require higher accuracy, please contact us.Model KT . KTV CHUCK BLOCK(μm)indicates theattractive face.End faceDimensions(Bottom face)Top faceSide faceEnd faceB B? B? B3 H LB3BB190°B2B3Side faceHBottom face (ON/OFF switchover face)KMV-M020 9.8N(1kgf)φ15(0.59) 20(0.78) 12(0.47) 2.0(0.07) 4(0.15) 20(0.78) 20(0.78) 0.06kg/0.13 lb×2KMV-M025 19.6N(2kgf)φ20(0.78) 25(0.98) 15(0.59) 2.5(0.09) 5(0.19) 25(0.98) 25(0.98) 0.13kg/0.28 lb×2KMV-M032 49 N(5kgf)φ25(0.98) 32(1.25) 20(0.78) 3.0(0.11) 6(0.23) 32(1.25) 32(1.25) 0.24kg/0.53 lb×2LMass[mm(in)]CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSELECTROMAGNETICCHUCKS〈KT-1〉LHP 1 P 2BAn example of usageKTV-1KT-1LP 1 P 2N〈KTV-1〉B90°N S N S N S N SHS N S N S N SP 1KT-4〈KT-2、3、4〉LP 2ModelBHNameplateTightening boltDimensions[Application]These blocks are used in combination with amagnetic chuck as an auxiliary tool to hold roundbars and sheet-like workpieces that are difficult tohold on the work face alone.[Features]●Since these blocks are not magnetizedthemselves, they are placed on a magnetic chuckto induce magnetism to hold workpieces.Magnetism can be induced on two faces of thetop face and side face or the V face and sideface.●Workpieces of special shapes can also be heldby use of chuck blocks, thus making it possibleto utilize your chucks in stock.●One set of two blocks has been finished together.(KT-3 and -4 are available individually.)Pole PitchB L H P? P?[mm(in)]MassKT-1 70(2.75) 100(3.93) 41(1.61) 3.2(0.12)2.0kg/4.4 lb×23.2(0.12)KT-2 45(1.77) 72(2.83) 22(0.86)0.37kg/0.8 lb×23(0.11)KT-3150(5.90)5.4kg/12 lb125(4.92)38(1.49) 4.5(0.17)KT-4 304(11.9) 2(0.07) 11.7kg/25 lbKTV-1 60(2.36) 65(2.55) 40(1.57) 3(0.11) 3.2(0.12) 0.78kg/1.7 lb×2※KTV-1 applicable diameter:φ10?φ70 mm※If you require additional working on the blocks, please contact us.BLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSMEASURINGTOOL HOLDERSMAGNETICHOLDERSMAGNETICTOOLS58