BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

MEASURING TOOL HOLDERSModel SMB MAGNETIC BASE FOR SENSOR FIXINGELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKS ELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSMEASURING MAGNETICTOOL HOLDERSHOLDERSMAGNETICTOOLS67ModelHolding Power※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.Mountable directlyon boring barMagnetic Holder BaseWidth Length HeightConventionalmeasuring methodMassModelRemark[mm(in)]SMB-1600N(60kgf) 40(1.57) 40(1.57) 40(1.57) 0.43kg/0.94lbSMB-1M 0.45kg/0.99lb Reflector providedModel MB-BRB BORER BASE*Hardness of V-face increased for longer life![Application]Model MB-S BORER BASE*HoldingPower250Nonφ70MB-S12BSMB-1MB-BRB38SMB-1M(Reflectorprovided)Mounting bracket asstandard accessory(210)70MB-BRB65Useful for measuring the projected amount of a cutter mounted on the arbor of a boringmachine with a dial gage to locate the cutter precisely.[Features]●The attractive face (V-face) has been hardened and therefore is less likely to bescratched and highly wear resistant.●The squareness of the face to secure the dial gage bracket to the V-face is within 5μm.●The dial gage mounting bracket for theφ8 stem comes as a standard accessory. Thebase can be put in use immediately after purchase.●The dial gage mounting bracket height is selectable. (2 stages)4- M2010790°〈MB-BRB65〉DimensionsHolding PartDimensionsWidth Length Height M Width AngleMax. Holding Max. Dia.Power to HoldThe max. holding power is based on a test piece ofφ38 round steel bar (SS400, Ra = 1.6).[mm(in)]MB-BRB38 45(1.77)35(1.37)55(2.16) M5(0.19) 38(1.49)thread,90°137N(14kgf)φ45(1.77)0.6kg/0.13 lbMB-BRB65 80(3.15)40(1.57)75(2.95) depth 8(0.31) 65(2.55)196N(20kgf)φ80(3.15) 1.1kg/2.4 lbModel Holding Power Arbor Diameter326580The dimensions marked by※depend on themounting of dial gages specified in JIS B7503.(21.2)※※Min.25Max.1404120°56 506017An example of sensormounting[Application]Suitable as a base for securing various sensors.[Features]●The ON/OFF selectable magnetic holder base and three-dimensionalbracket facilitate mounting/demounting and positional adjustment.●These bases are compact but produce a powerful magnetic force.●A mounting plate where various sensors can be mounted is includedas a standard accessory.75(87)4- MHolding Part DimensionsMB-S12B 250N(25kgf)onφ70(2.75)φ15(0.59)?120(4.72) 56(2.20) 120°1.3kg/2.8 lb121032790°384555Width(67)〈MB-BRB38〉14Shaft holderView Z: Sensormounting partdetailed dimensionsAngleφ85066ON/OFF leverLMassMass[Application]Useful for measuring the projected amount of a cutter mounted onthe arbor of a boring machine with a dial gage to locate the cutterprecisely.[Features]●The measuring tool holding arm can be freely locked by one-steptightening, which makes this base suitable for any length betweenits mounting position and the tip of the cutter.●Since a magnetic force is used for holding, the dial gage is heldfirmly even if it is mounted inclined. Further, the magnetic forcecan be turned on and off for easy mounting and demounting.●The dial gage is mounted by tightening the bracket with an M6bolt.[mm(in)]