BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

KMindicates the attractive face.An example of applicationKM-0018J, etc.ELECTROMAGNETICCHUCKSKM-0018HKM-0025H■OD“h”tolerance specificationModel■Plating specificationKM-0018JDimensionsHolding Surface MountingWorkable RangeTappedOD×Height“h”tolerance Height tolerancePower Treatment Hole D? D? H? H?KM-0005φ5(0.19)h7(0.27)×8(0.31)KM-0007φ7(0.27)h7(0.27)×8(0.31)KM-H001KM-H0015KM-H002KM-H0025φ10(0.39)h9(0.35)×15(0.59)φ15(0.59)h9(0.35)×15(0.59)φ20(0.78)h9(0.35)×15(0.59)φ26(1.02)h9(0.35)×25(0.98)These holders can be used to hold pieces cutout by wire cutting to prevent them frommoving or falling from the securing area.Upper Limitof WorkingTemp.Tapping[mm(in)]0?0.0120.3N(0.03kgf)5(0.19) 4.5(0.17) 1.5g/0.003 lb? ? Type B Not allowed.0?0.015 0.4N(0.04kgf) 7(0.27) 6.5(0.25) 2.5g/0.005 lb0?0.036 8N (0.8kgf) 10(0.39) 9.5(0.37)11g/0.024 lbPrepared hole up to0015 12?0.043 20N (2kgf) None None 15(0.59) 14(0.55) 3.0 deep on the rear 20g/0.044 lb?0.1(0.59)(0.47)0face allowed.?0.052 40N (4kgf) 20(0.78) 18(0.70) Type A40g/0.088 lb0?0.052 100N (10kgf) 26(1.02) 24(0.94) 25Prepared hole up to21100g/0.2224.0 deep on the rear(0.98)(0.82)lbface allowed.※The holding power may drop when the holder is worked on additionally. In particular, additional work in the※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.radial direction has large influence on the holding power and therefore, must be limited to a minimum necessary scope.[mm(in)]ModelOD×HeightHolding Surface MountingWorkable RangeUpper Limit ofPower Treatment Tapped Hole D? D? H? H? WorkingTemp.TappingMassKM-0005Lφ5(0.19)×13(0.51) 1.8N(0.18kgf)??2g/0.004 Ib13(0.51) 12(0.47)Type AKM-0007Lφ7(0.27)×13(0.51)4N (0.4kgf)7(0.27)6.5(0.25)Not allowed.3.8g/0.008 lbNoneKM-0010Hφ10(0.39)×8 (0.31)3N (0.3kgf)????Type B5g/0.011 lbPrepared hole up to 3.0 deep on the rear face allowed.11g/0.024 IbKM-001φ10(0.39)×15(0.59)8N (0.8kgf)10(0.39) 9.5(0.37)15(0.59)KM-T001φ10(0.39)×18(0.70)M5(0.19)Depth5(0.19)pitch0.8(0.03)18(0.70)Provided.12g/0.026 IbKM-0015φ15(0.59)×15(0.59)20N12(0.47) Type ANone15(0.59)(2kgf) Nickle15(0.59) 14(0.55)Prepared hole up to 3.0 deep on the rear face allowed.20g/0.044 IbKM-T0015φ15(0.59)×18(0.70)platingM5(0.19)Depth5(0.19)pitch0.8(0.03)18(0.70)Provided.23g/0.051 IbKM-0018Hφ18(0.70)×8 (0.31) 50N(5kgf)????Type BNot allowed.16g/0.035 IbNoneKM-002φ20(0.78)×15(0.59)40N(4kgf)20(0.78) 18(0.70)15(0.59)12(0.47)Type APrepared hole up to 3.0 deep on the rear face allowed.40g/0.088 IbKM-T002φ20(0.78)×18(0.70)M5(0.19)Depth5(0.19)pitch0.8(0.03)18(0.70)Provided.45g/0.100 IbKM-0025Hφ25(0.98)×10(0.39) 90N(9kgf)None????Type BNot allowed.38g/0.083 IbKM-T0025φ26(1.02)×30(1.18)100N(10kgf)M6(0.23)Depth10(0.39)pitch1.0(0.03)26(1.02)24(0.94)30(1.18)21(0.82)120g/0.266 IbType AProvided.KM-T003φ30(1.18)×33(1.29)150N(15kgf)M6(0.23)Depth8(0.31)pitch1.0(0.03) 30(1.18) 27(1.06)33(1.29) 28(1.10)180g/0.400 Ib※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.※The holding power may drop when the holder is worked on additionally. In particular, additional work in the radialdirection has large influence on the holding power and therefore, must be limited to a minimum necessary scope.■Peripheral knurling specification[mm(in)]ModelOD×HeightHolding PowerSurface TreatmentMounting Tapped HoleUpper Limit of Working Temp.FeatureMassKM-0010Jφ10(0.39)×8(0.31)3N(0.3kgf)5g/0.011 lbKM-0018Jφ18(0.70)×8(0.31)50N(5kgf)Nickle platingNoneType BPeripheral knurling16g/0.035 IbKM-0025Jφ25(0.98)×10(0.39)90N(9kgf)38g/0.083 Ib※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.First in the industry!indicates the attractive face.Stainless steel to resist rusting.MassCHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSMEASURINGTOOL HOLDERSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSKM-0010H-SUS KM-0018H-SUS KM-0025H-SUSWorking up to 0.5 mm allowed on the attractive face.Comparison in pure water (Left: Made of stainless steel)MAGNETICHOLDERS■Stainless steel specificationModel OD×Height Holding Power Surface Treatment Mounting Tapped Hole Upper Limit of Working Temp. Tapping MassKM-0010H-SUSφ10(0.39)×8(0.31) 3N(0.3kgf)KM-0018H-SUSφ18(0.70)×8(0.31) 50N(5kgf) None None Type B Not allowed.16g/0.035 Ib※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.5g/0.011 lbKM-0025H-SUSφ25(0.98)×10(0.39) 90N(9kgf) 38g/0.083 Ib[mm(in)]MAGNETICTOOLS82