BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

1.26 56111.212610131419MAGNETIC HOLDERSModel KM PERMANENT MAGNETIC HOLDERELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKS ELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSMEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS83R5indicates the attractive face.Model KM-T-T HEAT-RESISTANT PERMANENT MAGNETIC HOLDERindicates the attractive face.A heat-resistant type introduced topermanent magnetic holders!Model KM-RB HEXAGONAL PERMANENT MAGNETIC HOLDER (WITH MALE THREAD)Model KM-RT HEXAGONAL PERMANENT MAGNETIC HOLDER (WITH PLATE)M4KM-RB104030KM-RT10KM-025CKM-07C■Painting specificationModelOD×Height2- 4.5KM-RT10R6M44636KM-RT14HoldingPower2- 4.5M5KM-04CSurfaceTreatment※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.1010 5KM-RB1015MountingTapped HoleM610 614KM-RB1416indicates theattractive face.KM-08CKM-05CKM-025SThe T-bolt is available optionally.For KM-025C, 03C, 06SWorkable RangeD? D? H? H?Upper Limit ofWorking Temp.For KM-04C, 05CTappingKM-06SKM-025Cφ26(1.02)×25(0.98) 100N( 10kgf)M 6(0.23),depth 8(0.31) 26(1.02) 25(0.98) 90g/0.19 lb25(0.98) 17(0.66)KM-03Cφ30(1.18)×25(0.98) 150N( 15kgf) pitch1.0(0.03) 30(1.18) 27(1.06) 121g/0.26 lbKM-04Cφ40(1.57)×30(1.18) 300N( 30kgf) M 8(0.31),depth 12(0.47) 40(1.57) 36(1.41) 30(1.18)pitch1.25(0.04)Provided.Type CPainting(See page 81)20(0.78)260g/0.57 lbKM-05Cφ50(1.96)×40(1.57) 500N( 50kgf) 50(1.96) 46(1.81)545g/1.20 lbM12(0.47),depth 15(0.59)40(1.57) 25(0.98)KM-07Cφ70(2.75)×40(1.57) 700N( 70kgf)70(2.75) 60(2.36) 1000g/2.20 lbpitch1.75(0.06)M12(0.47),depth 18(0.70)KM-08Cφ80(3.14)×45(1.77) 1000N(100kgf)80(3.14) 66(2.59) 45(1.77) 27(1.06) 1600g/3.52 lbpitch1.75(0.06)Prepared hole up to 11 deepKM-025S 26(1.02)×26(1.02)×25(0.98) 100N( 10kgf) None 26(1.02)118g/0.26 lbon the rear face allowed.M6(0.23),depth 10(0.39)25(0.98) 25(0.98) 15(0.59)KM-06S 26(1.02)×60(2.36)×25(0.98) 200N( 20kgf)60(2.36) Provided 275g/0.60 lbpitch1.0(0.03)[mm(in)][Application]Most suitable as a securing fixture in workplaces where heat is generated such asship building and welding sites. These holders can also be used to hold downdrawings, rulers and small parts.[Features]KM-T004T●Heat resistance up to 350℃KM-T005T●The tapped hole provided on the back widens a scope of use by assembling theseholders to fixtures.[mm(in)]Upper Limit ofModel OD×Height Holding Power Surface Treatment Mounting Tapped HoleTappingMassWorking Temp.KM-T004Tφ40(1.57)×40(1.57) 300N(30kgf)M8(0.31)depth10(0.39)0.4kg/0.88 lbPaintingMax. 350℃Provided.KM-T005Tφ50(1.96)×45(1.77) 500N(50kgf) pitch1.25(0.04)0.67kg/1.47 lb※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.25φ6625φ6M6×P1.0Mass[Application]Used as a jig. Used for operations of conveying light weight workpieces in lines, etc.[Features]●The tip of the permanent magnetic holder is threaded, which enables the holder tobe mounted in any place easily.●When used in combination with the included plate, the holder can be mounted inplaces where a tapped hole cannot be made. (Model KM-RT)●Since this holder has been nickel plated, it can be used under various circumstances.ModelHolding PowerMassModelHolding PowerMassKM-RB1010N (1kgf)5g/0.011 lbKM-RT1010N (1kgf)10g/0.022 lbKM-RB1440N (4kgf)10g/0.022 lbKM-RT1440N (4kgf)18g/0.039 lb※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.40φ8640φ8M8×P1.25