BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

ELECTROMAGNETIC CHUCKPERMANENTPERMANENTCHUCKS CONTROLLERS MAGNETIC CHUCKS ELECTROMAGNETIC CHUCKSBLOCKSFOR MCMAGNETIC TOOLSModel HE-H HANDY HOLDERTransportation assist tool by use ofbattery-generated magnetic forceUseful for transportation ofcut-out plates or wastematerials at room temperatureand for taking out smallproducts!Holding power and battery lifeimproved significantly!φ5066 141〈HE-HS5A〉HE-HL5A50ON OFF ON釈放吸着[Application]These holders are used as a holding tool for moving and transporting cut-outplates or waste materials and taking out small products, etc.In addition, when cleaning areas around machine tools, if brushes are used,chips may be entangled and cleaning may not go smoothly. In such a case,these holders can be used to attract and remove them quickly.[Features]●Only with a small amount of electricity supplied by two D size alkalinebatteries, strong holding power is achieved.●These holders are of handy type which can be operated by one hand.They also do not have cord and therefore can be used in any places.●Since these holders are of hybrid type (complex structure of permanentmagnet and electromagnet), the held workpiece does not drop instantlywhen the batteries become dead, thus enhancing safety.●The batteries can be replaced easily without a tool. Also, commerciallyavailable rechargeable batteries can be used.Not heat-resistant, not water-tightN.P.145VACUUMCHUCKSMagnet holder(212)φ10〈HE-HL5A〉2550HE-HS5APROMELTA*SYSTEMSINE BARCHUCKSφ5091 (368)141Magnet holder(606)Model SL TOUCHERN.P.145φ10ON OFF ON釈放吸着25Model Type Max. Holding Power Power Source Working Rate MassHE-HS5A Short typeD size battery×21.8kg/3.96 lb600N(60kgf)50%EDHE-HL5A Long type (included)2.5kg/5.51 lb※The max. holding power is based on a test piece of SS400, 15 mm thick, ground surface, vertical pulingunder the most favorable conditions. Therefore, the lifting capacity is normally a third or less of the max.holding power. If workpiece are tilted or a force is applied to the magnet in a separating direction, the liftingcapacity will drop.※The mass includes the batteries.※This holder, even when attraction off, constantlygenerates holding power that is a third of the max. holding power at attraction on. However, the max.holding power at attraction off drops to 200 N (20 kgf). Exercise caution when using the holder.BLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSSL-1[Application]A simple transportationtool by use of a magnet.[Features]●Workpieces that are difficult to hold with hands can be carried by use ofthe quick attach/detach mechanism.●Useful for temporarily holding down or positioning small pieces in weldingwork.●Usable for a wide range of applications.[mm(in)]DimensionsModel Holding PowerMax.Height MassWidth Length HeightSL-1 500N(50kgf) 50(1.96) 92(3.62) 32(1.26) 122(4.80) 1kg/2.2 lb※The holding power is based on a test piece of SS400, 10 mm thick, pulled in the vertical direction.MEASURING MAGNETICTOOL HOLDERS HOLDERSMAGNETICTOOLS85Model HMB HAND MAGNET110 17 607017050 40HMB-7[Application]This product is useful in wide applications such as in machineshops, casting factories, food and chemical factories, etc. forcollecting iron chips, sorting screws by materials, collectingchips in cast sand, etc.[Features]●The magnetic force is turned ON/OFF easily with a handle.●Compact and strong holding power.●Capacity: Milling chips………about 0.2 kgM5×7 screws…about 0.5 kgModelHolding PowerMassHMB-7250N(25kgf)1.9kg/4,20 lb※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.