Summary
MAGNET_GENERAL_CATALOG_2019
MADE IN JAPANMAGNETIC TOOLS & EQUIPMENT FOR WELDING OPERATIONMT-A / WK / KM-WModel MT-A MAGSUPPORTER*Holdingpower800NMT-A-2Model KM-W MAGNETIC HOLDERHoldingPower200NKM-06WHoldingPower1300NKM-12W(16.7)75.258.5GMT-A-41.5G55(307)90°(252)30°1.5G(157)606644120 601354558.575.26486609060 12045 135Handle506055G(16.7)Model WK CLAMPER FOR WELDINGHoldingpower1000NHoldingpower1500NWK-3APrecautions for useWK-T3BHoldingpower1000NMax. 90°O31Max. 30°8025109 1098 21(157)φ84φ5052902.55(87)GOGGMT-A-21250150°120137OFFAn example of usage225G135[Application]Suitable for mating and keeping jointing parts of iron plates ormembers during welding work.[Features]A powerful holding type by use of a high-performance permanent magnet.MT-A-2●Both inside and outside welding are possible.●Any desired holding angle can be set in a range of 45°and 135°(angle scale provided).●ON/OFF function and V-groove provided.MT-A-4●Any desired holding angle can be set in a range of 30°and 90°(angle scale provided).●Angle adjustment with a handle.●ON/OFF function provided.[mm(in)]ModelHolding PowerMT-A-4 1500N(150kgf)×2 60(2.36)120(4.72)52(2.04)30°ー90°5 kg/11.0 lbThe holding power is based on a test piece of SS400, 10 mm thick, ground surface.〈Note 1〉〈Inside welding〉〈Outside welding〉WeldingpartHolder DimensionsWidth Length HeightWeldingpartHoldingAngleBoth welding types possible byusing an adequate attractive face.MassMT-A-2 800N( 80kgf)×2 50(1.96) 60(2.36)55(2.16)45°ー135°3.5kg/7.71 lb[Application]Suitable as a holding tool for welding on such work sites ofconstruction, bridge, ship building and piping.[Features]●The magnet part has a minimum necessary free rotating anglerange for easy mounting on workpieces.●The exterior of the magnet holder part is made of aluminum toprevent adhesion of iron powder on the top and side faces.●Model WK-T3B has a construction that is highly resistant to heat.●These clampers have a large mechanical strength towithstand rough handling.Model Max. Temperature Holding Power MassWK-3A 60℃WK-T3B 180℃1000N(100kgf)×2 2.3kg/5.07 lbThe holding power is based on a test piece of SS400, 10 mm thick, ground surface.[Application]Suitable for temporary holding during drilling and assembly.[Features]●Two magnets combined for easy angle setting.●An angle scale provided. (KM-12W)●The magnetic force can be turned on and off by operating the lever.(KM-12W)●The V-groove allows the holder to be attached to certain poles andcurved surfaces in addition to the flat surface. (KM-12W)[mm(in)]Holder DimensionsModel Holding PowerLengthHoldingMassWidth Length HeightAngleKM-06W 200N( 20kgf) 26 60 25 1290.7kg/1.54 lb(1.02) (2.36) (0.98) (5.07)FreeKM-12W 1300N(130kgf) 50 117 55 2734.5kg/9.92 lb(1.96) (4.60) (2.16) (10.75)※The holding power is per holder on one side and based on a test piece of SS400, 10 mmthick, ground surface.These holders cannot be used for work where heat is applied for long hours. If the magnet is subjected to high temperature,its magnetic force will drop or be lost suddenly, causing the workpiece to come off the attractive face. Exercise caution.MAGNETIC TOOLS & EQUIPMENTFOR WELDING OPERATIONLIFTINGMAGNETMAGBORE*CHIP & SLUDGECONVEYANCE EQUIPMENTENVIRONMENTALEQUIPMENTMAGNETIZER ANDDEMAGNETIZERMAGNETIC EQUIPMENTFOR CONVEYANCEMAGNETICSEPARATORSPOWERFUL MAGNETICSEPARATORSMEASURINGTOOLSMEASURINGINSTRUMENTSMAGNETICMATERIALS90
