BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

MAGNETIC TOOLS & EQUIPMENT FOR WELDING OPERATIONModel KM-SA HEXAGONAL MAGNETIC HOLDERMAGNETIC TOOLS & EQUIPMENTFOR WELDING OPERATIONLIFTINGMAGNETMAGBORE*CHIP & SLUDGE ENVIRONMENTAL MAGNETIZER AND MAGNETIC EQUIPMENTCONVEYANCE EQUIPMENT EQUIPMENT DEMAGNETIZER FOR CONVEYANCEMAGNETICSEPARATORSPOWERFUL MAGNETICSEPARATORSMEASURING MEASURING MAGNETICTOOLS INSTRUMENTS MATERIALS91KM-S1AHolding PowerSteel bar200ー300NSteel plate200ー600NKM-SAHolding PowerSteel bar600ー900NHoldingPowerSteel plate150ー250NKM-S10Steel plate1200ー1400NModel KM-S HEXAGONAL MAGNETIC HOLDER[Application]Usable for temporary holding during welding and temporary assembly. These holdershold workpieces firmly.[Features]●The holding angle can be set to 15°, 45°, 60°, 90°, 105°and 120°.●The magnetic force can be turned on and off.●The holding power on steel plates is about the same as when both faces of KM-S9 and S12 are used and at angles other than 105°, the holding power dropslittle when two faces are used.Precautions for use[Application]These holders provide strong holding power for temporary holding duringwelding and temporary assembly. These holders can also be used as a block.[Features]●The holding angle can be set to 45°, 90°and 135°.●The small type is equipped with a pushbutton and the large type with arotary handle for turning on and off the magnetic force.●The V-groove provided makes this holder to generate strong holding poweron curved surface as well as flat surface of workpieces. KM-SA:φ6 and over, KM-S1A:φ5 and overHoldingPowerSteel plate250ー450NKM-S136015 4511232 80GGGGGG2.96045 15GG47175205G112 13480 32 40 94G2.9(28) (39)(67)3.23.2(35) (39)(74)G80GNS[mm(in)]Holding PowerModelSteel barSteel plateDimensionsMassKM-SA600ー900N(60ー90kgf) 1200ー1400N(120ー140kgf)6.0kg/112(4.40)×112(4.40)×94(3.70){150ー200N(15ー20kgf)} { 800ー1000N( 80ー100kgf)} 13.2 lb200ー300N(20ー30kgf) 200ー600N( 20ー60kgf)KM-S1A60(2.36)×60(2.36)×47(1.85)0.85kg/{ 50ー70N( 5ー7kgf)} { 100ー350N( 10ー35kgf)} 1.87 lb※The holding power on steel plate is based on a test piece of SS400, 10 mm thick, ground surface.Note : The holding power in { } is for attraction on one face in the case of double-face attraction.ModelKM-S10KM-S13Holding PowerSteel Plate12095(54) (41)(51)(69)105°10545°45°15°OFF120°OFF15°120°G90°60°GG(80)(47)(104.4)(80)90°60°G15°120°(60)132.2Dimensions※The holding power on steel plate is based on a test piece of SS400, 10 mm thick,ground surface.ON15°120°45°ON45°105°105°(14)(14)[mm(in)]Mass150ー250N(15ー25kgf) 104(4.09)×95(3.74)×67(2.63) 0.9kg/1.98 lb250ー450N(25ー45kgf) 132(5.19)×120(4.72)×74(2.91) 1.6kg/3.52 lbThese holders cannot be used for work where heat is applied for long hours. If the magnet is subjected to high temperature,its magnetic force will drop or be lost suddenly, causing the workpiece to come off the attractive face. Exercise caution.